That was lucky
Moderators: Philip Whiteman, Andy Terry
That was lucky
I decided having used a set of cables for 2 years / 6000 miles that I should preemptively change them although there were no obvious problems. The rear gear cable was badly frayed inside the shifter, probably wouldn't have lasted much longer.
Does everybody else replace cables at any particular interval or just wait for them to break?
Does everybody else replace cables at any particular interval or just wait for them to break?
Eat cake before you're hungry
- Andy Terry
- Posts: 904
- Joined: 20 Nov 2006 14:27
- Real Name:
- Location: Bromsgrove, Worcs
Re: That was lucky
No. And never had one break.
I've always thought the most likely point of failure would be where the cable attaches to the nipple. But that's never actually happened to me either.
Instead of those cable end caps (ferrules?) that you crimp on with pliers and often fall off, I've started using heat shrink tube from Maplins.
http://www.maplin.co.uk/heat-shrinkable ... code=BF86T
I've always thought the most likely point of failure would be where the cable attaches to the nipple. But that's never actually happened to me either.
Instead of those cable end caps (ferrules?) that you crimp on with pliers and often fall off, I've started using heat shrink tube from Maplins.
http://www.maplin.co.uk/heat-shrinkable ... code=BF86T
Re: That was lucky
Crumbs, maybe I change gear too often.Andy Terry wrote:No. And never had one break.
Eat cake before you're hungry
Funny you should mention that Steve. Like you I never bother changing cables unless I'm upgrading the kit. I had my first rear mech cable break on the March Hare a couple of weeks ago which was most inconvenient. It broke close to the nipple and was clearly on the way out for some time by the way the cable had frayed. I don't intend to change cables more frequently but what I will do is to make a visual check of the cables periodically by pealing back the rubber sheathing on my Ergo shifters.
I would be far more concerned though if a brake cable were to fail. Has anybody experienced that?
I would be far more concerned though if a brake cable were to fail. Has anybody experienced that?
- Philip Whiteman
- Posts: 2046
- Joined: 19 Nov 2006 16:17
- Real Name:
- Location: Drayton, Worcestershire
I tend to replace mine about once every two years and oil the cables around every six months.
Additionally, I replace my pedals every three years as a matter of policy. That may seem extreme but I have suffered two critical failures in the past where the axle snapped in two. Some of you may remember my rant about Eggbeaters
Additionally, I replace my pedals every three years as a matter of policy. That may seem extreme but I have suffered two critical failures in the past where the axle snapped in two. Some of you may remember my rant about Eggbeaters
I have experienced one failure that I can recall. I don't know whether it applies in your case, Steve, but I strongly suspected that my failure was down to cable misalignment. If you drop the bike/have a minor collision, the levers sometimes get knocked out of position, and the natural inclination is just to push them back again. Or you may loosen them and re-tighten them when fitting new bar tape. Under such circumstances, the lever is liable to get moved a bit. Then the cable alignment may not be very good and/or the outer may not be fully seated in the mating recess. That leads to wear, a couple of strands snap, you get snagging, and the thing deteriorates quickly after that.
I've not personally had a brake cable fail but my friend's brake cable did break as we rolled into Little Langdale having just ridden over Hardknott and Wrynose. I guess it had come in for some heavy use in the preceding few miles but it did rather freak her out as she thought of what might have happened had it gone a few miles earlier..............Kermit wrote:I would be far more concerned though if a brake cable were to fail. Has anybody experienced that?
Gosh, I feel very old now as that was sometime in the last century.
Ruth